Product Categories

Additive Manufacturing

GeoDict provides a complete digital workflow for additive manufacturing: generate lattice and foam structures, simulate mechanical, flow, and electrical properties, and validate with experiments—reducing physical trials and accelerating development.

Consultation Hotline:

Product Details

GeoDict Applications · Additive Manufacturing

GeoDict provides a complete digital solution for additive manufacturing R&D. It can generate fully parameterized 3D lattice structures and perform topology optimization for specific applications, as well as analyze, model, and simulate open‑cell foam materials used in additive manufacturing. This helps users verify structural designs and predict material properties in a virtual environment, reducing experimental costs and accelerating product development.

Three representative application cases are summarized below.


Case 1: Digital Models for Additive Manufacturing – Lattice Structures in GeoDict

In additive manufacturing processes such as selective laser sintering (SLS) and direct metal laser sintering (DMLS), lattice structures are widely adopted for their advantages: weight reduction, improved mechanical properties, customizable thermal and electrical performance, and optimized flow characteristics.

GeoDict enables users to generate fully parameterized 3D models of various lattice structures and perform topology optimization for specific applications.

Strut‑Based Lattices

Using the GridGeo module, a wide variety of strut‑based lattice structures can be generated, including All Face Centered Cubic (AFCC), Auxetic, Body Centered Cubic with Z‑Strut (BCCZ), BCC, Cubic, Cuboctahedron Z, Diamond Penta Mode, FBCCXYZ, FBCCZ, FCCZ, Gyroid 7 (G7), Iso‑Truss, Kelvin, Octahedron, Octet‑Truss, Rhombic Dodecahedron, Tetrahedron‑Based, Truncated Cube, and Truncated Cuboctahedron.

Surface‑Based Lattices – TPMS

GridGeo also supports surface‑based lattice structures – Triply Periodic Minimal Surfaces (TPMS) – including cylindrical and square variants of Gyroid, I‑WP, Neovius, P‑W, Schwarz Diamond, and Schwarz Primitive.

For both types, users can precisely adjust geometric parameters and combine them with GeoDict's simulation modules to predict permeability, mechanical stiffness, thermal and electrical properties – enabling digital design and topology optimization before actual printing.


Case 2: Digital Twin of Aluminum Open‑Cell Foam

The properties of open‑cell metal materials depend largely on their pore space morphology. GeoDict offers a fully digital workflow:

Part 1: Image Processing & Analysis

CT scan data of open‑cell aluminum foam is imported and segmented. PoroDict identifies pores using a watershed algorithm – performing well even for highly open pore structures. To avoid distortion, only pores not intersecting the domain boundaries are analyzed.

Part 2: Statistical Digital Twin Creation

Based on the measured pore size distribution, FoamGeo creates a statistical digital twin with the same pore size distribution and pore content. Although not identical to the scanned model, it shares the same statistical characteristics. Validation compares pore size distribution and permeability between the scanned model and the digital twin.

Part 3: Digital Parametric Study

While keeping the pore size distribution unchanged, the solid volume fraction (SVF) is varied (10%, 13%, 17%, 20%) to study the influence of strut diameter on permeability, electrical conductivity, and stiffness. Results show that permeability decreases with increasing SVF, while conductivity and Young's modulus increase.

This workflow applies to materials produced by various manufacturing processes, including laser sintering, casting, foaming, and metal‑coated polyurethane foam. It enables digital material development without producing all physical variants, significantly shortening development cycles.


Case 3: Compression Simulation of Aluminum Foam – In‑Situ CT vs. GeoDict

Foam deformation under mechanical load is a complex process involving multiple mechanisms such as plastic deformation and buckling. In‑situ CT scanning – applying deformation during scanning – provides new insights into the mechanical behavior of cellular materials.

In collaboration with TESCAN, researchers conducted in‑situ CT compression tests on open‑cell aluminum foam and simulated the process with GeoDict:

TESCAN performed in‑situ CT scans of two foam samples

Math2Market analyzed the scans and built simulation models using GeoDict

The second scan was used for model validation

Part 1: Image Import & Processing

Scan data was imported and segmented. PoroDict identified pores via watershed algorithm. A total of 90 separate in‑situ CT scans were acquired during compression.

Part 2: Experiment vs. Simulation Comparison

Mechanical simulation was based on CT scan data of the uncompressed sample. ElastoDict uses the FFT‑based voxel solver FeelMath, which performs mechanical simulations directly on CT scan data without mesh generation – and also supports large‑deformation compression simulation of foams, a challenge for standard FEM solvers.

Simulation results matched the H112 heat treatment condition (E‑modulus 70 GPa, yield strength 23 MPa, elongation 23%). Except for initial stiffness differences likely caused by experimental setup limitations, the overall stress‑strain curves showed good agreement between simulation and experiment.

Key Findings

In‑situ CT scanning provides valuable insights into foam deformation

GeoDict simulations reproduce foam deformation very well

Experiment and simulation complement each other perfectly


Conclusion

From parametric modeling of diverse strut‑based and surface‑based lattice structures, to precise pore space analysis and statistical digital twin creation of open‑cell metal foams, to rigorous validation against in‑situ CT experiments – GeoDict provides a complete digital toolchain for structural design, performance prediction, and process optimization in additive manufacturing. Users can perform topology optimization and evaluate mechanical, flow, and electrical properties in a virtual environment without producing all physical variants, significantly shortening development cycles and reducing experimental costs.

It has a Class II qualification for steel structure engineering professional contracting and a Class II qualification for general contracting of building engineering construction; the company's main products include heavy steel, light steel, trusses and purlins, color steel plates and other steel structure products; in recent years, the company has undertaken a series of projects with significant influence, including large-scale structural components, bridges, garages, and standardized factories at home and abroad; products are exported to Belarus, Zambia, Indonesia and other countries, and have been well received.

Keywords: Additive Manufacturing

Related Products

Product Consultation

We will contact you within one working day. Please pay attention to your email.

%{tishi_zhanwei}%